X-Products Takes Shotgunning a Beer To A Whole New Level

The term "shotgunning a beer" takes on a whole new meaning with the Can Cannon from X Products.

The term “shotgunning a beer” takes on a whole new meaning with the Can Cannon from X Products.

In the “why the heck not” category is the new Can Cannon from X Products. Known for their rock solid drum magazines for modern sporting rifle designs, the X Products folks got a wild hair to bring something just plain fun to market. The Can Cannon is a complete upper assembly with a soda can diameter barrel. The upper unit contains a custom chamber, barrel extension and “barrel” with gas ports. The upper uses .223 blanks to create adequate gas pressure to launch the soda can down range. It’ll work with a full beer can too, but that would be a tragic waste of carefully fermented grains and hops, no?

In addition to no-excuses fun, the technology will be adapted to more practical uses like retriever training. The company hopes to develop similar versions capable to replicating gun shot noise while launching retrieval toys. Why not get some shooting in while training your hunting dog?

For more information, visit www.xproducts.com.

Blackhawk! AR-15 Vertical Grip: For Stability, Tactical Lights & Low Heat

Adding The Blackhawk! Rail Mount Vertical Grip

Moving right along with the Blackhawk! custom AR-15 project…

This time, I’m going to try out a complimentary accessory to the Blackhawk! Rail Mount Thumb Rest I installed last episode. The thumb rest can operate on its own to help grip, control and consistent hand placement. It also works great with a vertical grip.

The Blackhawk! Rail Mount Vertical Grip will work on most any rifle with a standard rail up front. Of course, if you want the grip to be on the bottom of the forend, you must have a rail on the bottom.

But first, why does one need a vertical grip?

  1. The grip is one layer removed from even the rail, so it’s not gonna heat up with lots of firing. Keeping freshly manicured hands away from that softness-robbing heat has got to be a benefit. Along with a daily soak on Palmolive.
  2. Control. The vertical grip presents a modified weapon support method. It’s especially handy for short-stock configurations, like indoor use.
  3. If you want to add a tactical light, it provides a great way to grip the rifle AND easily control a tail cap activated light. We’ll explore that in a future article.
  4. You have to admit, it looks cool. That counts for something right?
Blackhawk Rail Mount Vertical Grip

Here the Blackhawk! Rail Mount Vertical Grip is installed with the Blackhawk! Rail Mount Thumb Shelf – they play well together.

 

Blackhawk! Rail Mount Vertical Grip: Installation and features

Blackhawk Rail Mount Vertical Grip parts

The Blackhawk! Rail Mount Vertical Grip is modular in design, so you can customize the height of the grip. The standard vertical grip measures about 3 inches from the bottom of the rail. You can just fasten the included bottom cap to get a short post vertical grip configuration. This works great if you like to use the vertical grip as a partial hand support as shown in the photo later in this article. The kit also includes a grip extension that screws into the primary grip. This adds about 1 ⅝ inches so the total height of the vertical grip, with extension, is about 4 ⅝ inches. All of the parts are hollow and both the flat cap and extension grip piece include rubber gaskets to help seal the interior. This makes a handy place to safely store spare light batteries, small parts, cleaning supplies or maybe a few pieces of Bazooka Joe’s Bubble Gum. Your choice.

Blackhawk Rail Mount Vertical Grip installation

Since it’s a rail mount grip, installation is a snap. The grip itself has one half of a rail clamp molded in and a separate clamp for the opposite side. Two included hex bolts are used to fasten the grip to your rail. This provides a little extra flexibility for out of spec rails – you’ll still be able to get a solid mount.

Blackhawk Rail Mount Vertical Grip installation  1

The two included hex bolts are spaced to slide through grooves in the rail for forward / backward stability.

Blackhawk Rail Mount Vertical Grip water tight storage

The flat end cap has a rubber gasket to help keep moisture out of the storage area. Since there is not much surface on the flat one, there’s a large slot on the bottom to make it easier to remove. The extension piece also includes a gasket, but does not need a bottom slot and has a slightly rounded bottom.

Blackhawk Rail Mount Thumb Rest  2

Here’s the standard 3″ vertical grip installed with a Blackhawk! Rail Mount Thumb rest installed above and just forward of the Blackhawk! Rail Mount Vertical Grip.

Blackhawk Rail Mount Thumb Rest

The combination of the short vertical post and thumb rest works great. The thumb rest allows a little stable forward pressure and the vertical grip post allows a little backward pressure. The overall support-hand grip is rock solid. Of course, if you add the vertical grip extension, you have the additional option of using the vertical grip only with your support hand. In that configuration, you’re grasping the vertical grip more like a hammer.

One of the reasons I elected to install a vertical grip is that I’ll be trying out the Blackhawk! Offset Flashlight Rail Mount with a Blackhawk! Night-Ops Legacy L-6V tactical light. That one has a maximum output of 570 lumens, so maybe I’ll try it out at the 2013 Crimson Trace Midnight 3 Gun Invitational Match

Buy the Blackhawk! Rail Mount Vertical Grip Here

 

Half-Cocked: California Legal Assault Rifles…

Half-Cocked: California Legal Assault Rifle

Half-Cocked: We’re not that different, you and I…

Half-Cocked: We're not that different, you and I...

Half-Cocked: We're not that different, you and I...

Legal Disclosures about articles on My Gun Culture