Well, mostly this is an article about how to install an AR-15 flat-top front sight base and gas block. But we will share a few tips about how not to, learned the hard way, to save you aggravation should you choose to get adventurous with your own AR-15 rifle.

Here’s a pretty basic AR-15 rifle. This one happens to be a DPMS Lite 16 A3 AR-15. As you can see, it has the standard front sight base and gas block installed. While this piece looks to be permanently affixed to the rifle, it’s not. It’s just stuck on there, albeit really tightly, with a couple of pins.

AR 15 JP Gas Block Installation

Here’s a DPMS Lite 16 A3 AR-15. We’re going to replace the integral front sight base / gas block with a flat top version. So we can do a bunch of cool customizations to this rifle.

There’s nothing wrong with keeping the standard AR-15 front sight base, especially if you use no or low-power optics on your rifle. With a very low-power scope or red dot sight, you won’t really see the front sight (too much) and it makes a nice backup should your optic fail.

However, there are a number of good reasons you may want to consider removing the standard AR-15 sight block and replacing it with a flat top gas block.

Top 5 reasons to remove that ungainly AR-15 fixed front sight:

  1. While charging enemy positions, the wind resistance of the fixed AR-15 front sight slows you down.
  2. While it appears to double as a handy, integral bottle opener, you’ve come to your senses and determined that’s a really bad idea.
  3. Hardly any of Stickman’s rifles have one.
  4. You can use those cool AR-15 flip-up backup sights. Magpul, the company who just told Colorado politicians to enthusiastically pound sand, makes them. Support the resistance!
  5. If you use a scope, you can still kind of see the front sight getting in the way. It get’s really annoying with a higher-powered optic.

Whatever your reason, you can do this from the comfort of your home!

AR-15 JP Adjustable Gas Block System Installation

The JP Enterprise Adjustable Gas System

We have a number of reasons for embarking on this Dremel-free (hopefully) home-gunsmithing journey. You see, this rifle is going to be the starting point for a project we’re doing with the folks at Blackhawk!. As we wrote about earlier, Blackhawk! is making some really swell accessories for AR-15 style rifles, and putting a flat top gas block will give us a little more flexibility. Stay tuned!

After consulting the folks at Brownells.com, we decided to install the JP Enterprise Adjustable Gas System. We like the way it mounts with 3 solid hex screws and that it offers a quick-detach rail at standard height. This will allow us to mount a Blackhawk! backup sight system later. We also like the adjustable gas flow feature which allows you to tweak the amount of gas flowing back to the action. Adjust it so enough gas flows to ensure reliable operation with your favorite .223 or 5.56mm ammunition, but not so much that your rifle gets battered to bits over time.

Ready for some basic gunsmithing? Let’s go!

AR-15 Front Sight BaseHere’s our existing front sight base and gas block. It kinda looks permanent, but only because some parkerizing goop has been sloshed over the seams. It’ll come off with a little love and tenderness!
AR-15 JP Gas Block Installation remove upperFirst, remove the upper receiver from the lower. This will make things a lot easier.
AR-15 JP Gas Block Installation padded viseIn order to remove the front sight base, you’ll need to remove the flash hider or muzzle brake on your rifle. This will be much easier if you have a vise. Since we don’t have a dedicated barrel vise, we’re doing some budget improvisation and using an old kevlar vest as padding between our AR-15 barrel and those toothy vise jaws. What? It works…
AR-15 JP Gas Block Installation remove flash hiderOn our DPMS rifle, the flash hider was plenty tight, but not ridiculously so. A proper fitting wrench, a little elbow grease and some caution allowed us to take it right off.
AR-15 JP Gas Block Installation keep washerBe sure not to lose the washer. And pay attention to its orientation as this will go back on after the new gas block is installed.
AR-15 JP Gas Block Installation muzzle threadsNow the threaded end of your barrel is exposed. What a great time to brush the crud off!
AR-15 JP Gas Block Installation (1)The next step is to punch out the two lower pins that hold the sight base to the barrel. This picture shows our highly-sophisticated system for supporting the barrel and sight base while allowing the pins to get knocked out the bottom.
AR-15 Front Sight Bench BlockBetter yet, get this AR-15 bench block from Brownells.com. It’s specifically designed to support the front sight and has cutout holes for pin removal. You’re far less likely to ding up your rifle trying to pound out stubborn pins. It’s well worth the money, especially if you’re going to use it more than once. We got impatient waiting for ours and used the budget method, with the expected results…
AR-15 JP Gas Block Installation remove pinsIf you have brass punches, use them. You’ll be far less likely to ding up your existing sight base and your barrel. While brass leaves marks, it can be scrubbed off. Also, use a punch pin that is as close as possible to the diameter of the pin, without being larger. Using too small of a pin will “mush out” the pin and make it harder to remove. These pins are going to be pretty tight, so you’ll have to support the barrel well and smack the crud out of it. One of ours was so stubborn, we had to drill it out. Hopefully you won’t have to resort to that!
AR-15 JP Gas Block Installation gas tube pinNow remove the upper pin that holds the gas tube in place. This one will come out pretty easily. Be careful not to bend the gas tube. Try not to notice the brass marks where we fought that second pin with very little elegance.
AR-15 JP Gas Block Installation remove gas tubeNow the gas tube will pull out of the front sight base. And you have yet another great spring cleaning opportunity. Clean the interior and holes of the gas tube, but remember to leave it bone dry when finished.
AR-15 JP Gas Block Installation hammerHere’s another one of those right tool for the job opportunities. You’ll need to whack the front sight base towards the muzzle a couple of times to break it loose. A plastic hammer like this one from Brownells will do the job.
AR-15 JP Gas Block Installation remove sight blockOnce broken loose, the front sight assembly will slide forward and off the barrel. Here’s where you’ll get to see how much attention to detail was placed on your rifle’s manufacture. This barrel was not parkerized under the sight as you can see the bare steel.
AR-15 JP Gas Block Installation gas portYet another cleaning opportunity. If your rifle has been used, there will be some gas crud around the gas port. Clean it off and dry.
AR-15 JP Gas Block Installation adjustableNow we’re cookin’ with propane! Insert the gas regulator screw into the gas block just enough to hold it in place. Next, insert the gas tube, making sure to insert the right end.
AR-15 JP Gas Block Installation line up gas portBe sure that the hole in the gas tube aligns properly with the gas block port before the next step.
AR-15 JP Gas Block Installation (2)Slide the whole assembly into place, being careful not to bend the gas tube.
AR-15 JP Gas Block Installation (3)You’ll see the holes where the gas tube enters the receiver. Line everything up.
AR-15 JP Gas Block Installation (4)Once you’re confident that everything is in place, you can insert and tight the three hex screws that hold the gas block to the barrel. Now you can reinstall your flash hider or muzzle brake.
AR-15 JP Gas Block Installation completedThat’s it for the installation portion of this upgrade. Just replace your hand guards and reattach the upper and lower receivers. The next step has to be done at the range, so be sure to read on!

Adjusting the JP Enterprise Gas Block

Earlier we mentioned that you can tweak the gas flow using this particular JP Enterprises gas block. The process is a lot easier than it sounds.

  1. Bring your normal .223 and/or 5.56mm ammo to the range.
  2. Be SURE to bring the included hex wrench that fits the gas adjustment screw!
  3. Turn the gas adjustment screw (the silver one) all the way in to completely close off the gas port.
  4. Now back it out a couple of turns.
  5. Load and fire one shot.
  6. If the bolt of your rifle stays open, you’re likely done. If it does not, then you’re not getting enough gas. That sounds kind of wrong doesn’t it?
  7. If your bolt is not locking open on the last shot, keep opening the gas screw until the bolt locks back consistently on the last shot.
  8. When you get it set, you may want to use a little LocTite to keep it from moving around. Be sure to use low or medium strength so you can break the screw loose later if you need to!
  9. Just remember, if you change ammunition, you may need to readjust.

Next up, the Blackhawk! AR-15 upgrade project. Each article, we’ll document one part of the upgrade process.

Stay tuned!

 

You can find this at Brownells

J P Enterprises Ar-15/M16 Adjustable Gas Block
Loading…

IMPROVE YOUR SHOOTING!

SUBSCRIBE TO OUR NEWSLETTER AND GET A FREE EBOOK

Your weekly subscription will deliver what you need to know about guns, gear, ammo, shooting tips, and Second Amendment news. Delivered right to your inbox once a week, and no spam ever.